• EPDs are type III environmental declarations and are regulated by DIN EN ISO 14025 and DIN EN 15804. They contain quantifiable environmental information on a European harmonized, scientific basis. The data are developed by taking a holistic view of the product, optimization potentials along the material.
    Show
  • Stationary, atmospheric, welded, single or double walled thermoplastic tanks are widely used for the above ground storage of chemicals up to 100 m³. The BRL-K21009 requirements are based on the requirements of the DVS 2205-1 to DVS 2205-5 standards.
    Show
  • The EN 50131-2-4 standard is applicable for combined passive infrared and microwave detectors. This product will be used as part of intrusion alarm systems installed in buildings. The main standard is the EN 50131-2-4 for wired devices and for wireless devices the additional standard EN 50131-5-3 is required.
    Show
  • The type approval activities formerly conducted by the Swedish National Board of Physical Planning and Building, and later by Boverket (Swedish National Board of Housing, Building and Planning), have now been deregulated. In the new open system, w...
    Show
  • The EN 50131-4 standard is applicable for Warning devices. This is a device that gives an audible alarm in response to a notification warning device and may also provide alert indications.
    Show
  • Testing of polymer pipe joints, fitness for purpose
    Show
  • The energy distribution sector is continually evolving and changes inside and outside organisations follow on from one another at a rapid pace. These changes impact on the personnel, employees and manpower in organisations.
    Show
  • Kiwa experts | third party product inspections With product inspections a third party inspects the products and, if agreed, takes samples for testing.
    Show
  • Plastic pipes and fitting | Quality by certification and testing
    Show
  • The EN 50131-5-3 standard applies to intrusion alarm equipment using radio frequency (RF) links and located on protected premises. The EN 50131-5-3 standard defines the terms used in the field of intrusion alarm equipment using radio frequency links as well as the requirements relevant to the equipment.
    Show
  • Kiwa can test according to the TA Standard for safety flat-plate photovoltaic modules and panels (Solar). Testing and certification according to the UL1703 allows launching your products on the North American market. These requirements cover flat-...
    Show
  • Bio-ethanol and other liquid fueled fires are entering the European market. While Europe is working on a harmonised standard, the only regulation at the moment is the General Product Safety Directive for Consumer Products in combination with national laws.
    Show
  • If you have, or are developing, a new product in the area of heat energy distribution, such as delivery sets or heat pump systems, you obviously want to be sure that this product is as good as possible and that it complies with all the relevant standards.
    Show
  • Kiwa provides global testing and certification of domestic, commercial and industrial catering appliances.
    Show
  • Kiwa boasts a wide and in-depth experience as Notified Body from over 20 years in Medical Devices certification, with thousands of products already certified.
    Show
  • Activities for Australia and New Zealand-vKiwa and SAI Global have built up for many years an extensive co-operation in the field of sanitary products. Our laboratory is recognized by SAI Global, Global Mark, IAPMO Oceana and AGA for conducting tests according to Australian Standards.
    Show
  • Kiwa can test your PV inverters and grid connections. Kiwa is also Notified Body on all relevant directives that apply to inverters – electromagnetic compatibility directive (EMC-D), low voltage directive (LVD) and grid connection - our test facilities and expertise are available to you.
    Show
  • AS/EN 9100 Aerospace Quality Management certification: meet strict quality standards, demonstrate your commitment to quality and safety & meet customers’ needs.
    Show
  • EMAS certification with Kiwa: reduce your environmental impacts, engage employees and boost your reputation.
    Show
  • EN 15085 - The standart of the railway vehicles and their components with detailed rules on all welding requirements. To obtain a certification according to EN15085, inspection staff,equipment and production management must be proved that the requirements are fulfilled.
    Show