Utilities

The products are intended to be applied in The products are intended to be used as/in in hot water installations with a working pressure of maximum.1 MPa (10 bar) and a water temperature of maximum 90 °C. Remark: The technical specifications to be...

The recommended limits for correct operation are a dynamic pressure between 100 kPa and 500 kPa and a watertemperature of maximum 65°C. The flexible connecting hoses are intended for application in drinking water installations with a static waterp...

The products according BRL K536 G are applicable for piping systems distribution systems for hot and cold drinking water at a design (working) overpressure of 8 or 10 bar according the temperature profile table 1.

Organizing emergency drills allows network companies to assess and demonstrate that the organisation is ready and capable of handling a breakdown or emergency effectively. An emergency drill should be organised based on the emergency manual, with great attention being paid to preparation, execution and evaluation.

The float operated valves are intended to be applied in flushing cisterns which are connected to WC-pans. They have the purpose to open when the cistern is being flushed and shut off the water supply when the required water level is reached.The fl...

The products are intended to be applied in drinking water installations for the transport and distribution of hot and cold water.

Safe use of gas falls under your responsibility as a Housing Association or Owners Association (Vereniging Van Eigenaren or VVE). Analysing possible risks and the scope of those risks is of essential importance for this.

The sanitary tapware " single taps and mixer taps " are intended for application in drinking water installations with a static water pressure of maximum 1000 kPa and a maximum water temperature of 90°C. The recommended limits for correct operation...

Kiwa makes your quality visibleConfidence is what suppliers, buyers, inspectors and consumers need and want. Confidence in the quality of products can be demonstrated by means of the Kiwa Product Certificate.

The plumbing fittings are being used to make capillary soldering and/or thread connections, in tap water installations, household gas installations and in heating installations. The plumbing fittings are intended for use in combination with copper...

Kiwa makes your quality visibleConfidence is what suppliers, buyers, inspectors and consumers need and want. Confidence in the quality of the materials utilized, the performance of the products and the quality control on a day-to-day basis of the ...

For the drinking water sector in the Netherlands, we offer Kiwa quality Water Mark for an extensive range of products. The Kiwa Water Mark is commonly recognized in the drinking water sector in the Netherlands. Certificate holders are allowed to u...

The valves are meant as a device to prevent backflow. Check valves with a nominal diameter smaller then or equal 50 mm are intended for application in drinking water installations with a maximum constant temperature of 65°C and a with a maximum of one hour with a water temperature of 90° C.

Gas measurement takes place in the entire gas supply chain from gas production to delivery to industry and large business consumers and gas for household use. All the market parties benefit significantly (in financial terms) from correct and accurate gas measurement. Kiwa Technology advises these market parties.

The products according BRL K536 C are applicable for piping systems distribution systems for hot and cold drinking water at a design (working) overpressure of 8 or 10 bar according the temperature profile table 1.

The fittings with compression ends are being used to connect copper pipes, according to the Kiwa evaluation guideline BRL-K760, in tap water and gas installations and in heating installations. The tightening is achieved by a compression or cutting...

The products are intended to be applied as sanitary appliances giving a nominal flushing volume of 6, 7 or 9 litres. These appliances are intended for connection to drinking water installations with a maximum water temperature of 30° C and a maxim...

The Evaluation Guideline applies to coatings, produced in a dry form such as powder or in a liquid form such as paint, for protection against corrosion of metal attachments, piping, valves, pumps, tanks, pressure vessels and similar, for drinking-...

The headparts are intended to be used as part of sanitary tapware as meant in the Kiwa evaluation guidelines, for which a separate Kiwa product certificate has been issued; BRL-K610 “Thermostatic mixing valves”, BRL-K644 “Bib taps with integr...

The products according BRL 5610 are applicable for piping systems in heating distribution systems at a design (working) overpressure of 10 bar according the temperature profile class 5 in table 1.